Steve Powers (sgp@pani.cx)
Sun, 18 Apr 1999 04:13:32 +0100
--------
> > Sorry if this has been discussed before, but I've only just joined this list.
> > Is there support for the FreeCom DriveIn in the latest paride drivers, I'm
> > running generic 2.0.36. I don't seem to be able to get it to probe the drive
> > with a Mitsumi 8x ATAPI cdrom unit.
>
> I'm not familiar with all the marketing names for Freecom's products,
> but you may have their newer adapter, which is supported by the "friq"
> protocol module. friq is available in Alan's pre-2.0.37 kernels and
> in 2.2.
The DriveIN (http://www.freecom.de/e_drivein.htm) is a chassis unit into which
you place an ATAPI cdrom, dvd player etc.
I'm now using the paride from 2.0.37-pre-patch-10 and getting:
insmod paride
paride: version 1.04 installed
insmod friq
paride: friq registered as protocol 0
insmod pcd verbose=1
pcd0: friq: port 0x3bc, mode 0, test=(255,255,128)
pcd0: friq: port 0x3bc, mode 1, test=(255,255,128)
pcd0: friq: port 0x378, mode 0, test=(0,1,0)
pcd0: friq: port 0x378, mode 1, test=(0,1,0)
pcd0: friq: port 0x378, mode 2, test=(0,1,0)
pcd0: friq: port 0x378, mode 3, test=(0,1,0)
pcd0: friq: port 0x378, mode 4, test=(0,1,0)
pcd0: friq 1.01, Freecom IQ ASIC-2 adapter at 0x378, mode 4 (EPP-32), delay 1
pcd0: Reset (1) signature = 1 1 1 14 eb
pcd0: identify before command: alt=0x5a stat=0x58 err=0x100 loop=160001 phase=1
pcd0: Request sense before command: alt=0x5a stat=0x58 err=0x100 loop=160001
phase=1
pcd0: Reset (1) signature = 0 1 1 14 eb (incorrect)
pcd: No CDrom drive found
I try it again and get a different signature:
insmod pcd verbose=1
pcd: pcd version 1.05s, major 46, nice 0
pcd0: friq: port 0x3bc, mode 0, test=(255,255,128)
pcd0: friq: port 0x3bc, mode 1, test=(255,255,128)
pcd0: friq: port 0x378, mode 0, test=(1,1,0)
pcd0: friq: port 0x378, mode 1, test=(0,1,0)
pcd0: friq: port 0x378, mode 2, test=(0,1,0)
pcd0: friq: port 0x378, mode 3, test=(0,1,0)
pcd0: friq: port 0x378, mode 4, test=(0,1,0)
pcd0: friq 1.01, Freecom IQ ASIC-2 adapter at 0x378, mode 4 (EPP-32), delay 1
pcd0: Reset (1) signature = 1 1 1 14 eb
pcd0: identify before command: alt=0x5a stat=0x58 err=0x100 loop=160001 phase=1
pcd0: Request sense before command: alt=0x58 stat=0x58 err=0x100 loop=160001
phase=1
pcd0: Reset (101) signature = 80 80 80 80 80 (incorrect)
pcd: No CDrom drive found
Initialization of pcd failed
lsmod
Module: #pages: Used by:
friq 4 0
paride 1 [friq] 1
Then it fails completely as below until I reset the hardware with a power
cycle.
insmod pcd verbose=1
pcd: pcd version 1.05s, major 46, nice 0
pcd0: friq: port 0x3bc, mode 0, test=(255,255,128)
pcd0: friq: port 0x3bc, mode 1, test=(255,255,128)
pcd0: friq: port 0x378, mode 0, test=(255,255,0)
pcd0: friq: port 0x378, mode 1, test=(255,255,0)
pcd0: friq: port 0x378, mode 2, test=(255,255,0)
pcd0: friq: port 0x378, mode 3, test=(255,255,0)
pcd0: friq: port 0x378, mode 4, test=(255,255,0)
pcd0: friq: port 0x278, mode 0, test=(255,255,128)
pcd0: friq: port 0x278, mode 1, test=(255,255,128)
pcd0: friq: port 0x278, mode 2, test=(255,255,128)
pcd0: friq: port 0x278, mode 3, test=(255,255,128)
pcd0: friq: port 0x278, mode 4, test=(255,255,128)
pcd0: friq: port 0x268, mode 0, test=(255,255,128)
pcd0: friq: port 0x268, mode 1, test=(255,255,128)
pcd0: friq: port 0x268, mode 2, test=(255,255,128)
pcd0: friq: port 0x268, mode 3, test=(255,255,128)
pcd0: friq: port 0x268, mode 4, test=(255,255,128)
pcd0: friq: port 0x27c, mode 0, test=(255,255,128)
pcd0: friq: port 0x27c, mode 1, test=(255,255,128)
pcd0: friq: port 0x26c, mode 0, test=(255,255,128)
pcd0: friq: port 0x26c, mode 1, test=(255,255,128)
pcd0: Autoprobe failed
pcd: No CDrom drive found
Initialization of pcd failed
Cheers for the feedback,
Steve
-- To unsubscribe, send mail to: linux-parport-request@torque.net --
-- with the single word "unsubscribe" in the body of the message. --
This archive was generated by hypermail 2.0b3 on Sat 17 Apr 1999 - 22:14:58 EDT