urugvajo@geocities.com
Fri, 25 Jun 1999 15:30:28 +0000
I am ready to put my hands on this, but I need pointer to ATAPI
information (commands, and so on). Anybody has them?
Here are the outputs of the programs *without* modifications:
My configuration:
Cdwriter: HP CD-Writer+ 7500e
System: Debian 2.1 (Slink)
Kernel: 2.2.9
Cdrecord: 1.8.a20
Eduardo.
********** output of 'insmod pg verbose=100'
pg: pg version 1.02, major 97
pg0: epat: port 0x3bc, mode 0, ccr ff, test=(255,255,510)
pg0: epat: port 0x3bc, mode 1, ccr ff, test=(255,255,510)
pg0: epat: port 0x3bc, mode 2, ccr ff, test=(255,255,510)
pg0: 0x378 is parport0
pg0: epat: port 0x378, mode 0, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 1, ccr 40, test=(256,224,448)
pg0: epat: port 0x378, mode 2, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 3, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 4, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 5, ccr 0, test=(256,0,0)
pg0: Sharing parport0 at 0x378
pg0: epat 1.01, Shuttle EPAT chip c6 at 0x378, mode 5 (EPP-32), delay 1
pg0: Reset (1) signature = 8 8 8 8 8 (incorrect)
pg0: Reset (1) signature = 1 1 1 14 eb
pg0: Command sent, dlen=36 packet= 12 00 00 00 24 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 b0 00 c4 00 00 00 00 01 00 00 00 01 00 00 00
pg0: Read 36 bytes
pg0: HP CD-Writer+ 7500, slave
********** cdrecord's output
Cdrecord release 1.8a20 Copyright (C) 1995-1999 Jörg Schilling
Using remote (pipe) mode for interactive i/o.
TOC Type: 1 = CD-ROM
scsibus0:
0)
Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.001s timeout 40s
Executing 'test unit ready' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cmd finished after 0.001s timeout 40s
Executing 'inquiry' command on Bus 0 Target 0, Lun 0 timeout 40s
CDB: 12 00 00 00 24 00
cdrecord: Input/output error. inquiry: scsi sendcmd: retryable error
status: 0x2 (CHECK CONDITION)
CDB: 12 00 00 00 24 00
Sense Bytes: 70 00 05 00 00 00 00 12 00 00 00 00 24 00 00 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid)
resid: 36
cmd finished after 0.003s timeout 40s
Got 0 (0x0), expecting 36 (0x24) bytes of data.
Received Data:
error: 1 scb.chk: 1 sense_count: 18 sense.code: 0x70
'' '' '' NON CCS Disk
1)
Executing 'test unit ready' command on Bus 0 Target 1, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Success. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
*
2)
Executing 'test unit ready' command on Bus 0 Target 2, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Success. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
*
3)
Executing 'test unit ready' command on Bus 0 Target 3, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Success. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
*
4)
Executing 'test unit ready' command on Bus 0 Target 4, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Success. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
*
5)
Executing 'test unit ready' command on Bus 0 Target 5, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Success. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
*
6)
Executing 'test unit ready' command on Bus 0 Target 6, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Success. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
*
7)
Executing 'test unit ready' command on Bus 0 Target 7, Lun 0 timeout 40s
CDB: 00 00 00 00 00 00
cdrecord: Success. test unit ready: scsi sendcmd: fatal error
CDB: 00 00 00 00 00 00
cmd finished after 0.000s timeout 40s
*
********** debug of pg
pg: pg version 1.02, major 97
pg0: epat: port 0x3bc, mode 0, ccr ff, test=(255,255,510)
pg0: epat: port 0x3bc, mode 1, ccr ff, test=(255,255,510)
pg0: epat: port 0x3bc, mode 2, ccr ff, test=(255,255,510)
pg0: 0x378 is parport0
pg0: epat: port 0x378, mode 0, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 1, ccr 40, test=(256,224,448)
pg0: epat: port 0x378, mode 2, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 3, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 4, ccr 0, test=(256,0,0)
pg0: epat: port 0x378, mode 5, ccr 0, test=(256,0,0)
pg0: Sharing parport0 at 0x378
pg0: epat 1.01, Shuttle EPAT chip c6 at 0x378, mode 5 (EPP-32), delay 1
pg0: Reset (1) signature = 8 8 8 8 8 (incorrect)
pg0: Reset (1) signature = 1 1 1 14 eb
pg0: Command sent, dlen=36 packet= 12 00 00 00 24 00 00 00 00 00 00 00
pg0: Read 36 bytes
pg0: HP CD-Writer+ 7500, slave
pg0: Command sent, dlen=36 packet= 12 00 00 00 24 00 00 00 00 00 00 00
pg0: Read 36 bytes
pg0: HP CD-Writer+ 7500, slave
pg0: Command sent, dlen=0 packet= 00 00 00 00 00 00 00 00 00 00 00 00
pg0: completion: stat=0x51 err=0x64 phase=3
pg0: Command sent, dlen=18 packet= 03 00 00 00 12 00 00 00 00 00 00 00
pg0: Read 20 bytes
pg0: Command sent, dlen=0 packet= 00 00 00 00 00 00 00 00 00 00 00 00
pg0: Command sent, dlen=0 packet= 00 00 00 00 00 00 00 00 00 00 00 00
pg0: Command sent, dlen=36 packet= 12 00 00 00 24 00 00 00 28 00 00 00
pg0: completion: stat=0x51 err=0x54 phase=3
pg0: Command sent, dlen=18 packet= 03 00 00 00 12 00 00 00 00 00 00 00
pg0: Read 20 bytes
-- To unsubscribe, send mail to: linux-parport-request@torque.net --
-- with the single word "unsubscribe" in the body of the message. --
This archive was generated by hypermail 2.0b3 on Fri 25 Jun 1999 - 14:29:16 EDT