Re: [PARPORT] cdrecord 1.10 (write error - loss of streaming) problem

From: T K (zoerg@zworg.com)
Date: Fri Mar 02 2001 - 10:40:29 EST

  • Next message: T K: "Re: [PARPORT] cdrecord 1.10 (write error - loss of streaming) problem"

    schilling@fokus.gmd.de wrote:
    > >Starting new track at sector: 0
    > >Track 01: 19 of 302 MB written (fifo 0%).cdrecord: Input/output
    > >error. write_g1: scsi sendcmd: retryable error
    > >CDB: 2A 00 00 00 27 60 00 00 10 00
    > >status: 0x2 (CHECK CONDITION)
    > >Sense Bytes: F0 00 03 00 00 00 00 19 00 00 29 04 0C 09 00 00 FF FF
    > >Sense Key: 0x3 Medium Error, Segment 0
    > >Sense Code: 0x0C Qual 0x09 (write error - loss of streaming) Fru 0x0
    > >Sense flags: Blk 0 (valid)
    >
    > This is a buffer underrun - most likely caysed by a misconfigured
    > parallel port.
    >
    > Read README.parallel

    I went through the README's but perhaps I have overlooked something.
    From the kernel log I get:

    scsi0 : SCSI host adapter emulation for IDE ATAPI devices
    scsi : 1 host.
      Vendor: TOSHIBA Model: CD-ROM XM-5302TA Rev: 1095
      Type: CD-ROM ANSI SCSI revision: 02
    Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
    sr0: scsi3-mmc drive: 4x/4x xa/form2 cdda tray
    Uniform CD-ROM driver Revision: 3.10
    paride: version 1.04 installed
    paride: epat registered as protocol 0
    pg: pg version 1.02, major 97
    parport0: PC-style at 0x378 [SPP,PS2,EPP]
    parport_probe: failed
    parport0: no IEEE-1284 device present.
    pg0: 0x378 is parport0
    pg0: epat: port 0x378, mode 0, ccr 0, test=(256,0,0)
    pg0: epat: port 0x378, mode 1, ccr 40, test=(256,224,448)
    pg0: epat: port 0x378, mode 2, ccr 0, test=(256,0,0)
    pg0: epat: port 0x378, mode 3, ccr 0, test=(256,0,0)
    pg0: epat: port 0x378, mode 4, ccr 0, test=(256,0,0)
    pg0: epat: port 0x378, mode 5, ccr 0, test=(256,0,0)
    pg0: Sharing parport0 at 0x378
    pg0: epat 1.01, Shuttle EPAT chip c6 at 0x378, mode 5 (EPP-32), delay 0
    pg0: Reset (1) signature = 6f 6f 6f 6b 6f (incorrect)
    pg0: Reset (203) signature = 1 1 1 14 eb
    pg0: HP CD-Writer+ 7200, slave
    pg: pg version 1.02, major 97
    pg0: Sharing parport0 at 0x378
    pg0: epat 1.01, Shuttle EPAT chip c6 at 0x378, mode 2 (8-bit), delay 0
    pg0: HP CD-Writer+ 7200, slave

    Perhaps I need a delay other than 0?

    -- To unsubscribe, send mail to: linux-parport-request@torque.net --
    -- with the single word "unsubscribe" in the body of the message. --

    This archive was generated by hypermail 2b29 : Fri Mar 02 2001 - 10:41:19 EST