Marco Manzan (marco@fthp5.dem.uniud.it)
Tue, 16 Jun 1998 13:11:41 +0200
Hi,
I'm using a 7200 e as a writer, I successfully compiled the pg driver and loaded
it, the dmesg gives:
pg: pg version 1.0, major 97
pg0: epat: port 0x3bc, mode 0, ccr ff, test=(255,255,510)
pg0: epat: port 0x3bc, mode 1, ccr ff, test=(255,255,510)
pg0: epat: port 0x3bc, mode 2, ccr ff, test=(255,255,510)
pg0: 0x378 is parport0
pg0: epat: port 0x378, mode 0, ccr 0, test=(255,0,0)
pg0: epat: port 0x378, mode 1, ccr 40, test=(255,224,448)
pg0: epat: port 0x378, mode 2, ccr 0, test=(255,0,0)
pg0: epat: port 0x378, mode 3, ccr 0, test=(255,0,0)
pg0: epat: port 0x378, mode 4, ccr 0, test=(255,0,0)
pg0: epat: port 0x378, mode 5, ccr 0, test=(255,0,0)
pg0: Sharing parport0 at 0x378
pg0: epat 1.01, Shuttle EPAT chip c6 at 0x378, mode 5 (EPP-32), delay 1
pg0: Reset (6) signature = ff ff ff ff ff (incorrect)
pg0: Reset (203) signature = 1 1 1 14 eb
pg0: Command sent, dlen=36 packet= 12 00 00 00 24 00 00 00 00 00 00 00
pg0: Read 36 bytes
pg0: HP CD-Writer+ 7200, slave
to load it I had to change PG_TMO to 100.
All seams to work well, but when I tried to use cdrecord to burn the CD I got:
[[root@fthp5 marco]# cdrecord dev=0,0 speed=1 -v -dummy test.iso
Cdrecord release 1.6 Copyright (C) 1995-1998 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0'
scsibus: 0 target: 0 lun: 0
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'HP '
Identifikation : 'CD-Writer+ 7200 '
Revision : '2.02'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Track 01: data 3 MB
Total size: 4 MB (00:24.22) = 1817 sectors
Lout start: 4 MB (00:26/17) = 1817 sectors
Blocks total: 333750 Blocks remaining: 333750
resid: 48
cdrecord: Timer expired. Cannot send SCSI cmd via ioctl
The dmesg reads:
re = 1 1 1 14 eb
pg0: Command sent, dlen=36 packet= 12 00 00 00 24 00 00 00 00 00 00 00
pg0: Read 36 bytes
pg0: HP CD-Writer+ 7200, slave
pg0: Command sent, dlen=36 packet= 12 00 00 00 24 00 00 00 00 00 00 00
pg0: Read 36 bytes
pg0: HP CD-Writer+ 7200, slave
pg0: Command sent, dlen=0 packet= 00 00 00 00 00 00 00 00 00 00 00 00
pg0: completion: stat=0x51 err=0x60 phase=3
pg0: data done: stat=0x51 err=0x60 phase=3
pg0: Command sent, dlen=18 packet= 03 00 00 00 12 00 00 40 02 00 00 00
...
...
...
pg0: Command sent, dlen=60 packet= 5a 00 05 00 00 00 00 00 3c 00 06 08
pg0: Read 60 bytes
pg0: Command sent, dlen=60 packet= 55 10 00 00 00 00 00 00 3c 00 00 00
pg0: Write 12 bytes
pg0: before command: stat=0x58 err=0x0 phase=0 timeout
What can I do to burn the CD ?
Thanks in advance
Marco
-- _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ | | |Marco Manzan Email: marco@fthp1.dem.uniud.it | |Tel: (+39) 432 55 8020 Fax : (+39) 432 55 8027 | |Dipartimento di Energetica e Macchine | |Universita' degli Studi di Udine | |Via delle Scienze, 208 - 33100 Udine ITALIA | |_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _|-- To unsubscribe, send mail to: linux-parport-request@torque.net -- -- with the single word "unsubscribe" in the body of the message. --
This archive was generated by hypermail 2.0b3 on Wed 30 Dec 1998 - 10:17:51 EST