phil (philwh@gate.net)
Sat, 25 Sep 1999 12:24:29 -0400
I am having a problem with my Imation superdisk ls120
drive under Linux kernel 2.2.12.
I can only geg linux to recognize it if I first
load the dos driver.
Below is the output from my attempts.
First is trying to load the drivers with out
loading the dos driver,
then output from testport.exe,
and then the output from the dos driver and lastly
the output from the linux drivers loading successfully.
Can anyone help me with this problem, or must I always first
load the dos driver for this drive?
Do I need to do something with the pppscsi drivers, since the output
looks like it is a parallel scsi device?
thanks.
phil
---- unsuccessful loading of linux drivers---
insmod epat
paride: epat registered as protocol 0
insmod pf
pf: pf version 1.04, major 47, cluster 64, nice 0
pf0: Autoprobe failed
pf: No ATAPI disk detected
init_module: Device or resource busy
insmod pf verbose=1
pf: pf version 1.04, major 47, cluster 64, nice 0
pf0: epat: port 0x3bc, mode 0, ccr ff, test=(255,255,510)
pf0: epat: port 0x3bc, mode 1, ccr ff, test=(255,255,510)
pf0: epat: port 0x3bc, mode 2, ccr ff, test=(255,255,510)
pf0: epat: port 0x378, mode 0, ccr 0, test=(255,255,0)
pf0: epat: port 0x378, mode 1, ccr 40, test=(255,255,448)
pf0: epat: port 0x378, mode 2, ccr 0, test=(255,255,0)
pf0: epat: port 0x378, mode 3, ccr 0, test=(255,255,0)
pf0: epat: port 0x378, mode 4, ccr 0, test=(255,255,0)
pf0: epat: port 0x378, mode 5, ccr 0, test=(255,255,0)
pf0: epat: port 0x278, mode 0, ccr ff, test=(255,255,510)
pf0: epat: port 0x278, mode 1, ccr ff, test=(255,255,510)
pf0: epat: port 0x278, mode 2, ccr ff, test=(255,255,510)
pf0: epat: port 0x278, mode 3, ccr ff, test=(255,255,510)
pf0: epat: port 0x278, mode 4, ccr ff, test=(255,255,510)
pf0: epat: port 0x278, mode 5, ccr ff, test=(255,255,510)
pf0: epat: port 0x268, mode 0, ccr ff, test=(255,255,510)
pf0: epat: port 0x268, mode 1, ccr ff, test=(255,255,510)
pf0: epat: port 0x268, mode 2, ccr ff, test=(255,255,510)
pf0: epat: port 0x268, mode 3, ccr ff, test=(255,255,510)
pf0: epat: port 0x268, mode 4, ccr ff, test=(255,255,510)
pf0: epat: port 0x268, mode 5, ccr ff, test=(255,255,510)
pf0: epat: port 0x27c, mode 0, ccr ff, test=(255,255,510)
pf0: epat: port 0x27c, mode 1, ccr ff, test=(255,255,510)
pf0: epat: port 0x27c, mode 2, ccr ff, test=(255,255,510)
pf0: epat: port 0x26c, mode 0, ccr ff, test=(255,255,510)
pf0: epat: port 0x26c, mode 1, ccr ff, test=(255,255,510)
pf0: epat: port 0x26c, mode 2, ccr ff, test=(255,255,510)
pf0: Autoprobe failed
pf: No ATAPI disk detected
/lib/modules/2.2.12/misc/pf.o: init_module: Device or resource busy
---- output from testport.exe
TestPort (980730) Copyright (C) Micro Solutions Inc., DeKalb IL. 1994-1998
Engineering's Parallel Port Diagnostic Wizard Utility.
*****************************************************************************
LPT = 0378, C0 00 FF 00 00
Bidirectional
ECR Detected, 95 10 40 E0 00 C0 00 C2 02 EPP
Chipset : SMC FDC37C669
Mode : EPP
*****************************************************************************
--- output from dos driver
epatls
ASPI Manager For Dos Ver 5.46 Test1
Copyright Shuttle Technology.
Read Mode : EPP Fast
Write Mode : EPP Fast
HA #0: SHUTTLE EPATLS, PortBase:378, IRQ:7
Device #0: MATSHITALS-120 VER5 00
Driver Loaded Successfully.
--- successful loading of linux drivers after loading dos driver
paride: version 1.02 installed
paride: epat registered as protocol 0
pf: pf version 1.03s, major 47, cluster 64, nice 0
pf0: epat 1.01, Shuttle EPAT chip c8 at 0x378, mode 2 (8-bit), delay 1
pf0: MATSHITA LS-120 VER5 00, master LUN 0, type 0, removable, 246528 blocks
-- To unsubscribe, send mail to: linux-parport-request@torque.net --
-- with the single word "unsubscribe" in the body of the message. --
This archive was generated by hypermail 2.0b3 on Sat 25 Sep 1999 - 12:28:54 EDT