Hi all,
I've been battling to get an HP 5100C going and I am almost there.
ppscsi and epst are compiled into a 2.4.2 kernel.
sane 1.0.4 backend, frontend and xsane are installed.
I have finally been able to get xscanimage and xsane to recognise the scanner
after lots of searching and close regard to the FAQs.
Unfortunately I can only scan in black and white. Everything else leads to
device I/O errors.
i.e. I can type scanimage > test
But, e.g. scanimage --mode Color > test leads to device errors.
B&W speed is incredibly fast. I have seen it work once scanning color and it
was incredibly slow (it scans forward about a centimetre and then moves back
about 2/3).
Well I really hope someone can help.
Regards,
Adam
dmesg error messages follow (is this an SMP issue?):
..
VFS: Disk change detected on device sr(11,1)
VFS: Disk change detected on device sr(11,2)
VFS: Disk change detected on device sr(11,2)
VFS: Disk change detected on device sr(11,3)
VFS: Disk change detected on device sr(11,3)
epst.1: Command abort not supported
epst.1: Command aborted, bs=11 cb=6 db=5 bu=1 sg=0 rd=0 lp=32 pe=0 cc=2913
NMI Watchdog detected LOCKUP on CPU0, registers:
CPU: 0
EIP: 0010:[<c0238114>]
EFLAGS: 00000082
eax: 00002101 ebx: 00000202 ecx: 00002101 edx: cff36200
esi: ce7dd5a0 edi: 00000084 ebp: 0002cec8 esp: cf4edd10
ds: 0018 es: 0018 ss: 0018
Process syslogd (pid: 329, stackpage=cf4ed000)
Stack: 00000001 c019134a 00002101 00000000 cfeb3bc0 cbf156e0 c0137091 ce7dd5a0
00000001 ce7dd5a0 00000001 c0191404 00000001 ce7dd5a0 00001000 00000000
c0191693 00000001 ce7dd5a0 c01cc80f cf4ec000 00000282 d08ac4c0 c144ad40
Call Trace: [<c019134a>] [<c0137091>] [<c0191404>] [<c0191693>] [<c01cc80f>]
[<d08ac4c0>] [<c0136c04>]
[<c010ad85>] [<c01ed4c5>] [<c01ed657>] [<c01ee1ee>] [<c0225aa9>]
[<c0225b01>] [<c012ede3>] [<c0136f65>]
[<c0138134>] [<c0129cf6>] [<c0129d84>] [<c01350d6>] [<c01299c0>]
[<c0144c4e>] [<c0155c0c>] [<c01361ad>]
[<c01091c7>]
Code: 80 3d 28 cb 29 c0 00 f3 90 7e f5 e9 c5 83 f5 ff 80 3d 14 62
console shuts up ...
NMI Watchdog detected LOCKUP on CPU1, registers:
CPU: 1
EIP: 0010:[<d086c48c>]
EFLAGS: 00200082
eax: cba3ec60 ebx: cc943dd8 ecx: cba3ecb4 edx: 00000000
esi: 00200286 edi: ccc29eac ebp: cba3ec60 esp: ccc29de0
ds: 0018 es: 0018 ss: 0018
Process magicdev (pid: 752, stackpage=ccc29000)
Stack: ccc29e3c 000003e8 d08685ba cc943dd8 cba3ecb4 cba3ec60 00000000 d086264e
cba3ec60 00000000 00000000 00000000 d0862090 000003e8 00000005 00000000
00000000 00000001 ccc29e48 ccc29e48 c1465d40 ccc29e80 c01482bc 00000000
Call Trace: [<d08685ba>] [<d086264e>] [<d0862090>] [<c01482bc>] [<d086475c>]
[<d0864ed0>] [<d08b0157>]
[<d089cbf9>] [<d08a244c>] [<d089cc68>] [<c013cafc>] [<d08b080f>]
[<d089c3b8>] [<c013cd57>] [<c0134680>]
[<c01345ad>] [<c013fa2b>] [<c01348aa>] [<c01091c7>]
Code: 80 3d 28 cb 29 c0 00 f3 90 7e f5 e9 88 c0 ff ff 80 3d 28 cb
console shuts up ...
epst.1: Bus reset
epst.1: Command aborted, bs=12 cb=0 db=5 bu=0 sg=0 rd=0 lp=0 pe=0 cc=2913
epst.1: Command abort not supported
scsi : 1 host left.
epst.1: epst 0.92 (0.92), Shuttle EPST at 0x378 mode 2 (PS/2) dly 1 nice 0 sg
16
scsi0 : epst
Vendor: HP Model: C5190A Rev: 3740
Type: Processor ANSI SCSI revision: 02
Detected scsi generic sg4 at scsi0, channel 0, id 0, lun 0, type 3
epst.1: Command abort not supported
epst.1: Command aborted, bs=11 cb=6 db=5 bu=1 sg=0 rd=0 lp=32 pe=0 cc=1746
epst.1: Bus reset
epst.1: Command abort not supported
scsi : 1 host left.
parport0: epst.1 already owner
parport0: epst.1 tried to release parport when not owner
parport0: epst.1 already owner
parport0: epst.1 tried to release parport when not owner
parport0: epst.1 already owner
parport0: epst.1 tried to release parport when not owner
epst.1: epst 0.92 (0.92), Shuttle EPST at 0x378 mode 2 (PS/2) dly 1 nice 0 sg
16
scsi0 : epst
(I have an Abit BP6)
-- To unsubscribe, send mail to: linux-parport-request@torque.net --
-- with the single word "unsubscribe" in the body of the message. --
This archive was generated by hypermail 2b29 : Fri Feb 23 2001 - 08:21:36 EST