Jesse Alter (fuzzyl@alfheim.net)
Mon, 28 Dec 1998 21:01:35 -0500
Attached to this message is a file named dmesg.results. It is the
results of dmesg > dmesg.results after I issued the following commands:
insmod paride
insmod epat
insmod pd verbose=1
I will try to boot linux lp=0, as suggested by Grant earlier.
Thanks for all your help, I'll let you know if it solves my problem.
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fdb50
pcibios_init : BIOS32 Service Directory entry at 0xfdb60
pcibios_init : PCI BIOS revision 2.10 entry at 0xfdb81
Probing PCI hardware.
Calibrating delay loop.. ok - 332.60 BogoMIPS
Memory: 30860k/32768k available (768k kernel code, 384k reserved, 756k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP, IPIP
Linux IP multicast router 0.07.
VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.35 (Linux version 2.0.35 (root@summer) (gcc version egcs-2.90.29 980515 (egcs-1.0.3 release)) #3 Mon Oct 12 09:59:42 EDT 1998
Starting kswapd v 1.4.2.2
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
ide0: BM-DMA at 0xffa0-0xffa7
ide1: BM-DMA at 0xffa8-0xffaf
hda: WDC AC32500H, 2441MB w/128kB Cache, CHS=620/128/63, DMA
hdb: CD-ROM CDU311, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
tunnel: version v0.2b2
PPP: version 2.2.0 (dynamic channel allocation)
TCP compression code copyright 1989 Regents of the University of California
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
NET3 PLIP version 2.2 gniibe@mri.co.jp
plip1: Parallel port at 0x378, using assigned IRQ 7.
Partition check:
hda: hda1 hda2 hda3
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 64508k swap-space (priority -1)
paride: version 0.94 installed
paride: epat registered as protocol 0
pda: Autoprobe failed
pd: no valid drive found
registered device ppp0
pda: epat: port 0x3bc, mode 0, ccr ff, test=(255,255,510)
pda: epat: port 0x3bc, mode 1, ccr ff, test=(255,255,510)
pda: epat: port 0x3bc, mode 2, ccr ff, test=(255,255,510)
pda: epat: port 0x278, mode 0, ccr ff, test=(255,255,510)
pda: epat: port 0x278, mode 1, ccr ff, test=(255,255,510)
pda: epat: port 0x278, mode 2, ccr ff, test=(255,255,510)
pda: epat: port 0x278, mode 3, ccr ff, test=(255,255,510)
pda: epat: port 0x278, mode 4, ccr ff, test=(255,255,510)
pda: epat: port 0x278, mode 5, ccr ff, test=(255,255,510)
pda: epat: port 0x268, mode 0, ccr ff, test=(255,255,510)
pda: epat: port 0x268, mode 1, ccr ff, test=(255,255,510)
pda: epat: port 0x268, mode 2, ccr ff, test=(255,255,510)
pda: epat: port 0x268, mode 3, ccr ff, test=(255,255,510)
pda: epat: port 0x268, mode 4, ccr ff, test=(255,255,510)
pda: epat: port 0x268, mode 5, ccr ff, test=(255,255,510)
pda: epat: port 0x27c, mode 0, ccr ff, test=(255,255,510)
pda: epat: port 0x27c, mode 1, ccr ff, test=(255,255,510)
pda: epat: port 0x27c, mode 2, ccr ff, test=(255,255,510)
pda: epat: port 0x26c, mode 0, ccr ff, test=(255,255,510)
pda: epat: port 0x26c, mode 1, ccr ff, test=(255,255,510)
pda: epat: port 0x26c, mode 2, ccr ff, test=(255,255,510)
pda: Autoprobe failed
pd: no valid drive found
-- To unsubscribe, send mail to: linux-parport-request@torque.net --
-- with the single word "unsubscribe" in the body of the message. --
This archive was generated by hypermail 2.0b3 on Wed 30 Dec 1998 - 10:18:59 EST