Stephen Mollett wrote:
>>The mode is EPP.
>>after this mail, put the delay=0 and probe at 1x
>>speed. Not work :-(
>>
>
> Is your kernel configured for IEEE1284 modes
> (CONFIG_PARPORT_1284)? What parport-related messages
> do you get? (Specifically something like:
>
> parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
>
> is what you would expect to see if EPP is being
> detected.)
>
> Stephen
>
> __________________________________________________
> Do You Yahoo!?
> Everything you'll ever need on one web page
> from News and Sport to Email and Music Charts
> http://uk.my.yahoo.com
>
> -- To unsubscribe, send mail to: linux-parport-request@torque.net --
> -- with the single word "unsubscribe" in the body of the message. --
>
>
here is all the output of the modules and cdrecord (parport bios mode EPP)
#insmod pg drive0=0x378,0,0,-1,-1,0 verbose=1
#dmesg
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
parport0: Found 4 daisy-chained devices
parport0: only read 126 of 1000 ID bytes
parport0: device reported incorrect length field (34950, should be 127)
parport0 (addr 0): Legacy device
parport0 (addr 1): Printer, Canon BJC-1000
parport0 (addr 2): Printer, Canon BJC-1000
parport0 (addr 3): Printer, Canon BJC-1000
parport0: Printer, Canon BJC-1000
parport_pc: Via 686A parallel port: io=0x378
....
paride: version 1.06 installed (parport)
paride: epat registered as protocol 0
pg: pg version 1.02, major 97
pg0: 0x378 is parport0
pg0: epat: port 0x378, mode 0, ccr 0, test=(255,0,0)
pg0: epat: port 0x378, mode 1, ccr 0, test=(255,0,0)
pg0: epat: port 0x378, mode 2, ccr 0, test=(255,0,0)
pg0: epat: port 0x378, mode 3, ccr 0, test=(255,12,32)
pg0: epat: port 0x378, mode 4, ccr 0, test=(255,13,26)
pg0: epat: port 0x378, mode 5, ccr 2, test=(255,9,17)
pg0: Sharing parport0 at 0x378
pg0: epat 1.01, Shuttle EPAT chip c6 at 0x378, mode 2 (8-bit), delay 0
pg0: Reset (1001) signature = ff ff ff ff ff (incorrect)
pg0: Reset (1) signature = 1 1 1 14 eb
pg0: HP CD-Writer+ 7200, slave
#cdrecord -v dev=0,0 fs=32m speed=1 cdimage.iso
Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,0'
scsibus: 0 target: 0 lun: 0
Using libscg version 'schily-0.5'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'HP '
Identifikation : 'CD-Writer+ 7200 '
Revision : '3.01'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Drive buf size : 786432 = 768 KB
FIFO size : 33554432 = 32768 KB
Track 01: data 7 MB
Total size: 8 MB (00:47.81) = 3586 sectors
Lout start: 8 MB (00:49/61) = 3586 sectors
Current Secsize: 2048
ATIP start of lead in: -11625 (97:27/00)
ATIP start of lead out: 333750 (74:12/00)
Disk type: Phase change
Manuf. index: 0
Manufacturer: Illegal Manufacturer code
Blocks total: 333750 Blocks current: 333750 Blocks remaining: 330164
RBlocks total: 336246 RBlocks current: 336246 RBlocks remaining: 332660
Starting to write CD/DVD at speed 1 in write mode for single session.
Last chance to quit, starting real write in 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Track 01: 2 of 7 MB written (fifo 100%).cdrecord: Input/output
error. write_
g1: scsi sendcmd: no error
CDB: 2A 00 00 00 04 30 00 00 10 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F0 00 03 00 00 00 00 19 00 00 05 F5 0C 09 00 00 FF FF
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x09 (write error - loss of streaming) Fru 0x0
Sense flags: Blk 0 (valid)
cmd finished after 0.736s timeout 40s
write track data: error after 2195456 bytes
Sense Bytes: F0 00 00 00 00 00 00 19 00 00 05 E1 00 00 00 00 FF FF
Writing time: 24.316s
Fixating...
Fixating time: 164.149s
cdrecord: fifo had 224 puts and 68 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
-- Javier Andres Perez Barrientos <mailto:ra_atonp@yahoo.com> <home: +56(41)970440> <cell: +56(09)8247309>_________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com
-- To unsubscribe, send mail to: linux-parport-request@torque.net -- -- with the single word "unsubscribe" in the body of the message. --
This archive was generated by hypermail 2b29 : Mon Jan 07 2002 - 11:35:55 EST